How to Distinguish Between Single-Mode Fiber and Multi-Mode Fiber？

-

 

Optic fiber is a flexible transparent fiber made of extruded glass or plastic, slightly thicker than human hair. Optical fiber is the most commonly used means for transmitting light at both ends, and it is widely used in optical fiber communications. Optical fiber has longer transmission distance and higher bandwidth than wired cable. An optical fiber is usually composed of a transparent core with a low refractive index and a transparent cladding material. As an optical waveguide, the optical fiber causes total reflection of light in the core.

In general, there are two types of fibers: the supported multiple propagation paths or transverse mode fibers are called multimode fibers (MMF). In addition, the one that supports a single mode is called Single Mode Fiber (SMF).

1. What is Single-Mode Optical Fiber?

In optical fiber communication, single-mode fiber (SMF) is an optical fiber that directly transmits optical signals in the transverse mode. Single-mode fiber runs at a data rate of 100M/s or 1 G/s, and the transmission distance can reach at least 5 kilometers. Normally, single-mode fiber is used for long-distance signal transmission.

2. What is A Multi-Mode Optical Fiber?

Multi-Mode fiber (MMF) is mainly used for short-distance fiber communication, such as in buildings or campuses. The typical transmission speed is 100M/s, the transmission distance can reach 2km (100BASE-FX), 1 G/s can reach 1000m, and 10 G/s can reach 550m. There are two types of refractive index: graded refractive index and step refractive index.

3. What is the Difference Between Single-Mode and Multi-Mode Fiber?

1. Core Diameter

The main difference between multimode and single mode fiber is that: multimode fiber has a larger diameter. It is usually a core diameter of 50 or 62.5 µm. Typical single-mode fibers have core diameters of 8 and 10 µm, and both have a cladding diameter of 125 µm.

2. Light Source

Usually lasers and LEDs are used as light sources. Laser light sources are significantly more expensive than LED light sources. Because it produces light, it can be precisely controlled and has high power. While the light generated by LED light sources is more scattered (light in many modes), these light sources are mostly used in multimode fiber jumpers. At the same time, the laser light source (generating light in a single mode) is usually used for single-mode fiber patch cords.

3. Bandwidth

Since multi-mode fiber has a larger core size than single-mode fiber, it supports multiple transmission modes. In addition, like multi-mode fiber, single-mode fiber also exhibits modal dispersion caused by multiple spatial modes. But the modal dispersion of single-mode fiber is smaller than that of multi-mode fiber. For these reasons, single-mode fiber has a higher bandwidth than multi-mode fiber.

4. Sheath Color

The color of the sheath is sometimes used to distinguish between multimode fiber patch cords and multimode fiber patch cords. According to the definition of TIA-598C standard, for non-military use, single-mode fiber uses a yellow outer sheath, and multimode fiber uses an orange or aqua-green outer sheath. According to different types, some manufacturers use purple to distinguish high-performance OM4 fiber from other types of fiber.

5. Modal Dispersion

LED light sources are sometimes used in multimode fibers to create a series of wavelengths that propagate at different speeds. This will cause multi-mode dispersion, which limits the effective transmission distance of multi-mode fiber jumpers. In contrast, a laser used to drive a single-mode fiber produces a single wavelength of light. Therefore, its modal dispersion is much smaller than that of multimode fiber. Due to modal dispersion, multi-mode fiber has a higher pulse spread rate than single-mode fiber, which limits the information transmission capacity of multi-mode fiber.

6. Price

Multi-mode fiber can support multiple optical modes, and its price is higher than single-mode fiber. But in terms of equipment, solid-state laser diodes are usually used for single-mode fibers. Therefore, single-mode fiber equipment is more expensive than multi-mode fiber equipment. Therefore, the cost of using multi-mode fiber is much less than the cost of using single-mode fiber.

 

 

Comments

Post a Comment

Popular posts from this blog

Analysis of The Causes of Cable Insulation Breakdown and Preventive Measures

-
Image
We combine our experience in cable operation over the years with the application of solid Bauer edge theory to analyze the causes of insulation breakdown of power cables.  The purpose is to cast a brick to attract jade, and electrical counterparts to find specific measures to prevent cable insulation breakdown , improve the level of safe operation of the cable and extend the service life of the cable. I. Breakdown of Solid Insulation 1. Solid insulation breakdown of the form of insulation material is also known as dielectric. When the voltage applied to the dielectric exceeds a certain critical value, the electric field strength in the dielectric exceeds the level it can withstand. Through the dielectric current increases sharply, the dielectric rupture or decomposition, the complete loss of insulation capacity. This phenomenon is called dielectric breakdown. Different dielectric, the form, and mechanisms of breakdown are different, field dielectric breakdown can generally be divid...
Read more

Precautions for OPPC Cables During Transportation and Installation

-
Image
 For OPPC phase line fiber optic cable conductor, due to the existence of discharge, over the pulley, tightening the line caused by the structure elongation and operation of the temperature rise in the process of expansion elongation and creep elongation generated by plastic deformation, so the fiber residual length requirements are very strict. Fiber optic units should have good mechanical protection to ensure that the fiber is not extruded. To prevent moisture intrusion and affect the service life of the fiber, the fiber should be placed in a closed tube, or take other moisture-proof measures. Then OPPC phase line fiber optic cable wire in the transportation and installation process should pay attention to what issues? 1. The cable tray with fiber optic cable should be rolled in the direction indicated on the side of the plate. Rolling distance should not be too long, and generally should not exceed 20 meters, rolling should pay attention to prevent obstacles to damage the packa...
Read more

What are The Main Methods of Power Cable Withstand Voltage Test

-
Image
A cable withstand voltage test is a way to find faults in the presence of cables. It is easily affected by various factors during the test, resulting in problems such as failure and short circuits. The main methods of several cables to withstand voltage tests are described below. The First, Ultra-Low Frequency Withstand Voltage Test The ultra-low frequency (0.1Hz) withstand voltage test method first appeared in 1980. And it is mainly a non-destructive test method for observing whether there is an insulation defect in cable operation. And the method has been verified by a large number of laboratory tests and field tests.  The low-frequency withstand voltage test has a good application effect in the low-voltage power cable withstand voltage test. The method utilizes the principle of converting 50 Hz alternating current into direct current voltage through rectification and filtering.  And then converting the direct current voltage into an alternating current voltage of 1 kHz thro...
Read more